Відео

So not much help its virtually built i need instructions from flat pack

Well done Mr. Witkowski 😀👍

Genuine question are the turn ups high enough to stop water from blowing up and under ?

great videos thanks

I just notice under the sheet. There's downlights, how do you run cabling for those downlights? Look like the foam sandwiched between the sheets.

It is a really good idea to do in the shed but is it going to be waterproof or is it going to lakewater when it rains?

Also can you reverse door direction during install?

What do you do with the silicone???

How long does it take for polystyrene to decompose. I've used this twice. Also look in the video at the polystyrene blowing all over the joint. How do you get away with the polution. Both times I've used it what a mess. It looks like it has snowed. And why don't you cut the gutter part off in the factory. It's it because of laziness or money. I will never ever use this product again. Polluters of the 21st century. Disgusting. Shamefull.

Make sure the metal sheet curves into the door frame when you attach it, and attach a little shy of the edge. The goal is to align the sheets so that once the door flashing is rivetted on, you can get all four screws in the hinges biting into the door frame. Do it wrong, and only two of the screws will be usable.

Not too bad. The manual forgets the push taps for the floor and this fellow secured the floor with one screw instead of 3 (as per manual). When on its side, there are an additional 2 screw that screw in towards the back at the left and right most areas of the floor (just like the roof screws). All in all a pretty nice unit, and this colour is handy if you have an average lit garage and want to be able too see the storage space better.

I bought a 6x3x2.4 m high wall gable roof "single garage shed" with roller door. Instructions are general. I am a handy man but never built sheds, I was hoping to receive in my email pack "of how to step by step" how to build my own shed i bought and not receive a general email with this video attached to it and other advertising stuff. STRATCO AU, is it that complicated to have a specific instruction for the shed i bought? Am i expecting too much for a 5900$ shed? Make your product easily read and understood by simple handy men not just builders- this is how you increase your market. I need a simple step by step guide how to install my shed, thanks

Mostly clear but ... the installation of the suspension bracket is confusing. Why don't you show this at the start with 'if you're using a suspension bracket' do this ... ? Also the location of the bracket on the back channel isn't mentioned. Flush at each end? and what? 125mm from the bottom of the channel? Would help to know what size holes to pre-drill or if it's only a pilot hole then say so at the part where he's drilling

ThanksYoui!!!!

Nice shed, would love them in a bigger size. Please introduce more size options.

Full. Support. This. Channel ♥️👍👌👍

Fantastic. Thank you.

looks cool in black ! how big is it?

Reciprocating saw or cutting wheel on your grinder would have been faster

That roller door installation is hilarious didn’t level it didn’t tension it 🤣🤣🤣🤣

This is definatley not clear enough to actually do this job. Very poor effort by Stratco.

Utterly useless

Great video. Cheers

it appears to be the Rack-it system, although it also appears as though the bench top is not supported by the top rails? The rail mid span braces sit below the upper surface of the rail so also don't support the bench top. Rail doesn't need a brace if there is no load on it! .... and what's supporting the bench top?

This is not that simple. Channels will not align with sheet metal, no pilot holes in door jamb. What is portrayed as a 'simple' task is nervous breakdown inducing.

Fresh healthy lawn thats why they eat the lawn 🪲 cause the problem

I've bought one of those sheds . Install came to a halt because there's no instructions anywhere for where the reinforcement header beams go . Any help anyone ?

Don't quit your day job

Absolutely like the videos guys from Geelong Victoria 👍🇦🇺😀

why would you bury the lemon try so low, wouldn't it get trunk rot?

The problem is which is the best way to waterproof the bottom rail so that no water can flow into the inside of the shed ?

You laid the decking upside down! the fluted side goes down, it's designed for ventilation with the floor frame. Helps to stop rot.

You think they would put wood stringers on the inside so you can get a place to put a screw into.

I got 12 aluminium spacers and 30 off m2x90 bolts and nuts but zero instructions of where these are suposed to go! My deck is 4.7m x 1.75 free standing. numbers dont make any sense regardless of which type of corners I use?????????????????????????

With covid behind us is national patio day back this year?

Is it possibly to install the door so it opens to the right and not left?

*PromoSM*

GUtter is way to high, bodge job guys.

Not bad but you're much better off getting a 19mm spanner underneath than using the crappy hex key as it doesn't have enough leverage and the tops of the legs round off.

$200 + $90 delivery, not available in stores :(

I would like to put this in an Absco shed. The corrugations are about 15cm apart, which means this window will not fit perfectly on the over flutes. Would this mean water will get in around the sides?

What about wild birds?

They don’t reply

What size is this?

Why at 50 seconds it seys to use screws

Thank you for taking the time to show how to attach that 2nd upright rail! Other videos don't. ❤

Bloody awesome instructional and installation video, covered just about everything you’d need to know for the DIY or potential buyer. Many thanx

What happens if you get diabetes?